sliding the new camshaft bearing shell over proper

adapter.

(2) Position the rear bearing in the tool. Install

horseshoe lock and by reversing removal procedure,

carefully drive bearing shell into place.

(3) Install the remaining bearings in the same

manner. The Bearings must be carefully aligned

to bring oil holes into full register with oil pas-

sages from the main bearing. If the camshaft

bearing shell oil holes are not in exact align-

ment, remove and install them correctly.

(4) Install a new rear plate o-ring at the rear of

camshaft. Be sure this seal does not leak.

OIL PAN

REMOVAL

(1) Disconnect the negative battery cable.

(2) Raise the vehicle on hoist.

(3) Drain the oil.

(4) Remove the oil pan lower cover (Fig. 45).

(5) Remove the bolts from oil pan. Remove the 6

bolts that are on the inside of the oil pan.

(6) Remove the oil pan.

INSTALLATION

(1) Remove all gasket material from cylinder block.

Be careful not gouge or scratch aluminum pan seal-

ing surface.

(2) Apply a continuous 3 mm bead of Silicone

Sealer to oil pan, install within 10 minutes. Install

the oil pan.

(3) Install the inside oil pan bolts. Torque bolts to

11 N·m (8 ft. lbs.).

(4) Torque the smaller oil pan bolts to 11 N·m (8 ft.

lbs.). Torque the larger oil pan bolts to 25 N·m (18 ft.

lbs.).

(5) Install the oil drain plug. Torque to 79 N·m (58

ft. lbs).

(6) Lower the vehicle from hoist.

(7) Fill engine with proper amount of oil.

(8) Connect the negative battery cable.

OIL PUMP

REMOVAL

(1) Disconnect the negative battery cable.

(2) Remove the timing gear cover. Refer to timing

gear cover removal and installation in this section).

(3) Remove the oil pump (Fig. 46).

INSTALLATION

(1) Install new O-ring and lubricate with clean

engine oil.

(2) Install the oil pump. Torque screws to 27.5 N·m

(20 ft. lbs.). Check for normal backlash between

pump and crankshaft gears.

(3) Install the timing gear cover. Refer to timing

gear cover removal and installation in this section.

INTERNAL VACUUM PUMP

REMOVAL

(1) Disconnect the negative battery cable.

Fig. 45 Oil Pan

1 – LOWER OIL PAN COVER

2 – OIL DRAIN PLUG

Fig. 46 Oil Pump Removal

1 – CAMSHAFT GEAR

2 – CRANKSHAFT GEAR

3 – OIL PUMP

4 – VACUUM PUMP

XJ ENGINE 9 - 33

REMOVAL AND INSTALLATION (Continued)

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 51 52

Komentarze do niniejszej Instrukcji

Brak uwag

Ergotron T-Slot Bracket manuály

Uživatelské manuály a uživatelské příručky pro Montážní sady Ergotron T-Slot Bracket.
Poskytujeme 1 manuály pdf Ergotron T-Slot Bracket ke stažení zdarma podle typů dokumentů: Uživatelská příručka

Ergotron T-Slot Bracket Uživatelská příručka (2 strany)

Značka: Ergotron | Kategorie: Mounting kits | Velikost: 0.68 MB |

Tabulka s obsahem

User's Guide

888-97-190-W-00 rev.B • 04/11

Další produkty a příručky pro Montážní sady Ergotron

Modely	Typ Dokumentu
NF VESA Adaptor, 63"	Manuál s instrukcemi Ergotron NF VESA Adaptor, 63", 3 stránky
Neo-Flex Keyboard Wall Mount	Uživatelská příručka Ergotron Neo-Flex Keyboard Wall Mount, 6 stránky
T-Slot Bracket Kit	Manuál Ergotron T-Slot Bracket Kit, 4 stránky
Utility Shelf for StyleView 40/41/42 Carts	Manuál Ergotron Utility Shelf for StyleView 40/41/42 Carts, 6 stránky
Power Strip Mounting Kit for Carts	Manuál Ergotron Power Strip Mounting Kit for Carts, 4 stránky
NF Basket and Handle Kit	Manuál Ergotron NF Basket and Handle Kit, 2 stránky
DS100 Sliding Display Bracket	Manuál Ergotron DS100 Sliding Display Bracket, 4 stránky
Worksurface for WorkFit-A	Manuál Ergotron Worksurface for WorkFit-A, 2 stránky
NF Unistrut Pole Adaptor	Manuál s instrukcemi Ergotron NF Unistrut Pole Adaptor, 3 stránky

Arrow VM1012-B Dokumentacja Strona 33

Komentarze do niniejszej Instrukcji

Ergotron T-Slot Bracket manuály

Ergotron T-Slot Bracket Uživatelská příručka (2 strany)

Tabulka s obsahem

Další produkty a příručky pro Montážní sady Ergotron